3D打印钛合金多孔材料对体外成骨细胞系MC3T3-E1的生物安全性

基础医学与临床 ›› 2020, Vol. 40 ›› Issue (10): 1374-1380.

3D打印钛合金多孔材料对体外成骨细胞系MC3T3-E1的生物安全性

景丽¹, 史文², 曹雨², 刘瑞赛², 刘璐², 李建宇², 刘辉^1*

1.天津市第三中心医院肝胆疾病研究所天津市重症疾病体外生命支持重点实验室, 天津 300170;
2.嘉思特华剑医疗器材(天津)有限公司天津市骨植入物界面功能化与个性化研究重点实验室, 天津 300190

收稿日期:2020-03-03 修回日期:2020-05-22 出版日期:2020-10-05 发布日期:2020-09-29
通讯作者: ^* liuyangmeimei@163.com
基金资助:
天津市科技支撑重点项目(18YFZCSY00890);天津市自然科学基金 (18JCYBJC29000); 天津市企业重点实验室开放基金(SY-04-201902)

Biosafety of 3D printed titanium alloy porous materials to osteoblast cell line MC3T3-E1

JING Li¹, SHI Wen², CAO Yu², LIU Rui-sai², LIU Lu², LI Jian-yu², LIU Hui^1*

1. Tianjin Key Laboratory of Extracorporeal Life Support for Critical Diseases, Institute of Hepatobiliary Disease, Tianjin Third Central Hospital, Tianjin 300170;
2. Tianjin Key Laboratory of Interforce Functionality and Personalization of Bone Implants, Just Huajian Medical Device (Tianjin) Co. Ltd, Tianjin 300190, China

Received:2020-03-03 Revised:2020-05-22 Online:2020-10-05 Published:2020-09-29
Contact: ^* liuyangmeimei@163.com

摘要/Abstract

摘要： 目的利用电子束熔融成型技术(EBM)3D打印钛合金多孔支架材料,检测其对成骨细胞(OB)的生物安全性。方法打印3种拓扑单元结构的多孔钛合金材料(2.0、2.25及2.5 mm的Dode-Medium单元结构),制备各组材料在多个时间点的浸提液(浸泡时间设24、48、72、96 h),并将浸提液用于成骨细胞系MC3T3-E1的体外培养。通过MTT实验,计算成骨细胞的相对增殖率(RGR);通过苏木精-伊红(HE)染色,形态学观察成骨细胞的生长状态;通过碱性磷酸酶(ALP)测定,分析成骨细胞的分化活性;通过免疫荧光染色,观察成骨细胞中I型胶原(Col Ⅰ)的表达水平。结果在各组材料浸提液孵育下,成骨细胞贴壁牢固、增殖活跃,生长状态良好。与DMEM孵育的阴性对照组比较,各材料浸提液组成骨细胞的相对增殖率无显著性差异;与DMSO孵育的阳性对照组比较,各材料浸提液组成骨细胞的相对增殖率显著升高(P＜0.01);各组材料浸提液的细胞毒性程度评估均≤1。与DMEM孵育的阴性对照组比较,各材料浸提液组成骨细胞的ALP活性与Col Ⅰ含量均无显著性差异;与DMSO孵育的阳性对照组比较,各材料浸提液组成骨细胞的ALP活性与Col Ⅰ含量均显著升高(P＜0.01)。结论以EBM技术3D打印钛合金多孔材料,其浸提液不会影响成骨细胞的体外增殖与分化,即具有良好的生物安全性。

关键词: 钛合金, 3D打印, 多孔材料, 生物安全性, 成骨细胞

Abstract: Objective To prepare 3D-printed porous materials of titanium alloy by electron beaming melting (EBM) and to confirm its biosafety to osteoblasts (OB). Methods Three topological structures of titanium alloy porous materials (2.0 mm, 2.25 mm and 2.5 mm Dode-Medium structure) were prepared by 3D printing technology. The extracts of titanium alloy porous materials were collected at multiple time points (24,48,72,96 h) and used for in vitro culture of osteoblasts cell line MC3T3-E1. The relative growth rate (RGR) of osteoblasts was cal-culated by MTT test. The morphological observation of osteoblasts was performed by HE staining. The activity of ALP was determined for analyzing the differentiate capacity of osteoblasts. The expressional level of Col Ⅰ in osteoblasts was assessed by immunofluorescence staining. Results Following incubation with extracts of titanium alloy porous materials, the osteoblasts were found to adhere and proliferate actively. There was no significant difference in the RGR of osteoblasts between extract group and the negative control group of DMEM. However, the RGR of osteoblasts increased significantly in extract groups compared with that in the positive control group of DMSO (P＜0.01). The cytotoxic degree of osteoblasts in extract groups was all less than or equal to 1. There was no significant difference in the level of ALP and Col Ⅰ of osteoblasts between extract groups and the negative control group of DMEM. However, the level of ALP and Col Ⅰ of osteoblasts enhanced significantly in extract groups compared with that in the positive control group of DMSO (P＜0.01). Conclusions The extracts of titanium alloy materials do not affect the proliferation and differentiation of osteoblasts in vitro that confirmed its biosafety.

Key words: titanium alloy, 3D printing, porous materials, biosafety, osteoblast

中图分类号:

R318.08

景丽, 史文, 曹雨, 刘瑞赛, 刘璐, 李建宇, 刘辉. 3D打印钛合金多孔材料对体外成骨细胞系MC3T3-E1的生物安全性[J]. 基础医学与临床, 2020, 40(10): 1374-1380.

JING Li, SHI Wen, CAO Yu, LIU Rui-sai, LIU Lu, LI Jian-yu, LIU Hui. Biosafety of 3D printed titanium alloy porous materials to osteoblast cell line MC3T3-E1[J]. Basic & Clinical Medicine, 2020, 40(10): 1374-1380.

参考文献

[1] Zhang C, Zhang L, Liu L, et al. Mechanical behavior of a titanium alloy scaffold mimicking trabecular structure [J]. J Orthop Surg Res, 2020, 15: 40-51.
[2] Cruz RS, Lemos CAA, Oliveira HFF, et al. Comparison of the use of titanium-zirconium alloy and titanium alloy in dental implants: a systematic review and meta-analysis [J]. J Oral Implantol, 2018, 44: 305-312.
[3] Tahayeri A, Morgan M, Fugolin AP, et al. 3D printed versus conventionally cured provisional crown and bridge dental materials [J]. Dent Mater, 2018, 34: 192-200.
[4] 朱伟尧, 刘蕊, 战德松, 等. 3D打印含铜钴基合金与PDLF细胞生物相容性初探[J]. 表面技术, 2019, 48: 324-331.
[5] 楼毅, 张志文. 3D打印三维多孔海洋贝壳/鹿瓜多肽支架材料的生物相容性[J]. 中国组织工程研究, 2019, 23: 5497-5502.
[6] Piszczek P, Radtke A, Ehlert M, et al. Comprehensive evaluation of the biological properties of surface-modified titanium alloy implants [J]. J Clin Med, 2020, 9,342:doi:10.3390/jcm9020342.
[7] Ackland DC, Robinson D, Redhead M, et al. A personalized 3D-printed prosthetic joint replacement for the human temporomandibular joint: from implant design to implantation [J]. J Mech Behav Biomed Mater, 2017, 69: 404-411.
[8] Nagarajan N, Dupret-Bories A, Karabulut E, et al. Enabling personalized implant and controllable biosystem development through 3D printing [J]. Biotechnol Adv, 2018, 36: 521-533.
[9] Li WW, Zhang SK, Liu J, et al. Vitamin K2 stimulates MC3T3-E1 osteoblast differentiation and mineralization through autophagy induction [J]. Mol Med Rep, 2019, 19: 3676-3684.
[10] Kim I, Kim JH, Kim K, et al. The IRF2BP2-KLF2 axis regulates osteoclast and osteoblast differentiation [J]. BMB Rep, 2019, 52: 469-474.
[11] Chai XY, Zhang WC, Chang BY, et al. GPR39 agonist TC-G 1008 promotes osteoblast differentiation and mineralization in MC3T3-E1 cells [J]. Artif Cells Nanomed Biotechnol, 2019, 47: 3569-3576.
[12] Liu XY, Song XB, Zhang P, et al. Effects of nano tantalum implants on inducing osteoblast proliferation and differentiation [J]. Exp Ther Med, 2016, 12: 3541-3544.